loading

Professional bead mill, mixers manufacturer and factory - Polyc

Pigment Milling Equipment: Types, Selection and How to Compare Manufacturers

Which machine for which pigment, and how to compare

Pigment processing guide

Pigment milling is not one operation. Wetting out a powder, breaking up agglomerates and reducing primary particles are three different jobs, and they do not happen in the same machine. Most pigment lines that underperform are not short of equipment — they are using the right machines in the wrong order, or asking a disperser to do a mill's work.

This guide covers the four machine routes, which pigment belongs on which, the media sizes that set your fineness ceiling, and the four questions that separate one equipment manufacturer from another.

By Marin Hu, POLYC technical contentUpdated November 2026
Horizontal bead mill used for pigment dispersion and milling
A horizontal bead mill on the assembly floor. For pigment work the chamber and rotor material matter more than the motor rating, because wear is what changes the product over time.

Quick Answer: What Pigment Milling Requires

Pigment milling requires two distinct stages, and the distinction explains most equipment mistakes. Dispersion wets the powder and breaks agglomerates apart; it happens at high speed in a turbulent field and needs no grinding media. Milling reduces the primary particles themselves; it requires grinding media and a chamber where those media can be energised.

If the Hegman gauge stops improving after dispersion, you have hit the disperser's ceiling and no additional disperser time will move it. That is the signal to move to media milling — not a sign that the disperser is too small.

If your situation isThe usual routeBecause
Powder still visible, gauge fallingHigh speed disperserWetting and de-agglomeration, no media needed yet
Gauge plateaued above targetBead or basket millOnly media reduce primary particles
Paste too stiff to pumpThree roll millMedia milling needs a flowable vehicle
Frequent color changes, small batchesBasket millSingle vessel, cleaning confined to the basket
Sub-micron or nano targetHorizontal bead mill, small mediaEnergy density and separation gap become the constraint

Pigment Milling at a Glance: 8 Parameters

The whole decision in one table, for readers who need the shape of it before the detail.

ParameterTypical rangeNotes
Core functionDispersion + size reductionUsually two machines, not one
Grinding media0.2 – 1.5 mm zirconia or ceramicPOLYC media mill specification range
Achievable fineness50 nm – 5 µmMedia and pass strategy dependent
Practical coating target5 – 20 µmHegman 6–7 for most architectural coatings
Media mill batch size6 L – 300 L working volumePZB and PZP ranges
Viscosity handled by media millFlowable, pumpable pasteStiffer pastes go to a three roll mill
Color/product changeBasket mill fastestHorizontal mill needs flushing between colors
Best fitFrequent colors, tight fineness specShort runs favour basket, volume favours horizontal

Milling Is Not Dispersion

This is the first-principle distinction that decides equipment spend, and it is worth stating plainly because the two are routinely conflated in supplier literature.

A pigment powder arrives as agglomerates — clusters of primary particles held together by van der Waals forces and moisture. Dispersion replaces the air and moisture between those particles with vehicle, and breaks the clusters into their individual primary particles. A serrated high speed disperser does this with turbulence and shear in the liquid. It is fast, it runs at low energy per liter, and it has a hard floor: it cannot make a primary particle smaller than it already is.

Milling is what happens when you need the primary particle itself to be smaller — for higher opacity, better gloss, stronger color development or a specific transparency. That requires media: small hard bodies that collide with the particle and fracture it. No amount of disperser speed substitutes for this, because the energy has to arrive as a mechanical contact against the particle, not as fluid turbulence.

The operational consequence is a diagnostic. Track Hegman fineness during dispersion. If it rises and then plateaus, the plateau is the primary particle size of that pigment lot. Everything beyond it is milling work.

The 4 Routes: Which Machine for Which Pigment

Four machine families cover pigment processing. They are not competitors so much as different stages and different viscosity regimes.

MachineWhat it actually doesViscosityChangeoverBest for
High speed disperserWets powder, breaks agglomerates. No media, no size reduction.Low to mediumFastEvery pigment line, first stage
Basket millDispersion and milling in one vessel, integrated pump.Low to mediumFastestShort runs, many colors
Horizontal bead millTrue particle size reduction with small media, high energy density.Flowable pasteNeeds flushingVolume, tight fineness, sub-micron
Three roll millShear between rolls, no media. Handles very stiff paste.Very high, non-pourableSlowHigh-viscosity, concentrated pigment

The common mistake is treating these as alternatives to be chosen once. In practice a pigment line runs them in sequence: disperser to wet out, bead mill to reduce, and a three roll mill only where the paste is too stiff to pump. A single machine asked to do all three will do one of them badly.

The Process Map: Pigment, Mill, 0.2-1.5 mm Bead, Fineness

Different pigment chemistries are not equally hard to disperse. The table below maps the pigment class to the machine and media size that usually suits it, based on how the pigment wets out and how hard its agglomerates are.

Pigment classTypical difficultyUsual machineStarting bead sizeTarget d50
Titanium dioxide (inorganic white)Low — wets readily, soft agglomeratesHigh speed disperser, often no mill1.0 – 1.5 mm if milled10 – 20 µm
Iron oxide and other inorganic colorsLow to medium — dense, settles fastDisperser + bead or basket mill0.8 – 1.2 mm5 – 15 µm
Azo pigments (yellow, red, orange)Medium — needs wetting timeDisperser + horizontal bead mill0.6 – 1.0 mm2 – 8 µm
Phthalocyanine (blue, green)High — hard agglomerates, needs energyHorizontal bead mill, high energy0.3 – 0.6 mm0.5 – 2 µm
Carbon blackHighest — very low bulk density, hard to wetDisperser with high shear + bead mill0.3 – 0.5 mm0.5 – 2 µm
Transparent / nano pigmentVery high — requires fine media and long residenceHorizontal bead mill with dynamic gap0.1 – 0.3 mm< 0.5 µm

Bead sizes and fineness targets above are general industry guidance for each pigment class, not figures measured by POLYC on your material. The achievable result depends on pigment grade, solids loading, vehicle and pass strategy — which is why we recommend a trial on your own material before fixing a specification.

Read the table as a starting point for a trial, not a specification. Two suppliers of the same nominally identical pigment can behave differently if their surface treatment or moisture content differs — which is why the trial matters more than the table.

Grinding Media: 0.2-1.5 mm Sets the Fineness Ceiling

Media do the grinding, so media choice is machine choice. Three parameters decide the outcome, and a fourth decides how often you revisit it.

Diameter

The achievable particle size scales roughly with bead diameter — as a working rule the target is about one thousandth of the bead size. Smaller media give finer grind and more contact points, but they carry less energy each, are harder to retain, and require more passes.

Density

Higher density media carry more momentum at the same tip speed, which grinds harder and wears the chamber faster. Zirconia is the usual production choice for its balance of density and wear resistance; ceramic grades suit contamination-sensitive work; glass is the lowest-cost option and the gentlest.

Fill level

Media fill is typically 75 to 85 percent of chamber volume. Too little and energy transfer per bead is low; too much and the media cannot move freely, shaft load climbs and the mill behaves as if blocked. Fill level is the parameter most often set once and never revisited when the product changes.

Wear, the fourth parameter

Media wear changes the particle size distribution over time: a mill that reached 5 microns on fresh media will not hold that figure once the beads have worn into a range of smaller sizes. Media consumption per tonne of product is a more useful purchasing number than media price per kilogram, because a low-cost bead that wears twice as fast does not stay low-cost.

The 4 Problems That Decide Color Strength

Color strength is the commercial outcome of the whole process, and it fails in four characteristic ways.

1. Over-grinding past the strength peak

Color strength does not rise indefinitely with fineness. Each pigment peaks at a particular particle size, and beyond it the increased surface area and reactivity work against you. Running a mill longer is not automatically running it better — past the peak you are spending energy and heat to lose strength.

2. Flocculation after the grind

Freshly milled particles have high surface energy and will re-agglomerate if the vehicle and dispersant system cannot hold them apart. The symptom is a paint that reads correctly on the gauge but loses gloss, opacity or shade in the can after a few days. The mill did its job; the let-down did not.

3. Heat

At grinding viscosity nearly all shaft power ends up as heat in the product. Heat accelerates flocculation and can shift shade on heat-sensitive organics. The cooling water figures in the specification tables are the flow needed to remove that heat at rated power — running below them does not create less heat, it just raises product temperature until something else limits the batch.

4. Contamination from wear

Chamber, rotor and media all wear, and the wear products end up in the pigment. On light shades and high-transparency grades this shows as dulling long before any mechanical failure. Wetted-part material selection is therefore a product-quality decision, not only a maintenance one.

Lab, Pilot, Production: 3 Scales, One Media Size

Scaling a pigment grind is not a matter of multiplying volume. Energy density and residence time have to be held constant, otherwise a formulation that worked in the lab behaves differently at production scale.

ScaleTypical batchWhat it is forWatch out for
Lab / bench0.5 – 5 LFormulation, media trials, color matchingCooling is easy at this size, so heat problems stay hidden
Pilot20 – 200 LScale-up validation, small production runsThe first place temperature rise becomes real
Production500 L and aboveVolume outputPass strategy and pump circuit now dominate the result

The most common scale-up failure is heat: a lab mill has a large surface-to-volume ratio and sheds heat easily, so a formulation that ran cool in the lab can exceed its temperature ceiling on the first production batch. Sizing the cooling circuit for rated power rather than for the lab result is what prevents it.

PZB Pin Type: 6 Models from 6 to 150 L

The pin type horizontal range, for pigment work where concentrated energy is required. Where a cell shows two motor values those are the alternative drives available on that frame.

ModelWorking volume (L)Motor power (kW)Hourly capacity (L/h)Cooling water (L/h)
PZB-6615100–2001,000
PZB-101018.5200–5001,500
PZB-202030300–6002,000
PZB-303037 / 45500–8002,000
PZB-606075600–1,5002,500
PZB-150150160 / 200800–2,0004,000

Note the cooling water column: the PZB-150 needs 4,000 liters per hour to remove the heat from its drive at rated load. A plant that plumbed for a 30 kW machine and later upsized will find cooling, not grinding, becomes the limit.

PZP Static Disc: 6 Models from 15 to 300 L

The static disc range, for products that need a gentler shear field or where the target is mid-range rather than sub-micron. Lower power for a given chamber volume is the point: a PZP-30 uses 30 kW where a PZB-30 uses 37 to 45 kW.

ModelWorking volume (L)Motor power (kW)Hourly capacity (L/h)Cooling water (L/h)
PZP-151515200–500500
PZP-303030500–1,0001,000
PZP-606037 / 45800–2,0002,000
PZP-100100551,000–3,0002,500
PZP-150150752,000–5,0003,000
PZP-30030090 / 1103,000–6,0005,000

Both ranges share the same chamber geometry family, so a plant running a small PZB for development and a large PZP for production is comparing like with like when it scales a formulation up.

How to Compare Pigment Milling Equipment Manufacturers

Published capacity tables are the easiest thing in this industry to copy. Two suppliers quoting the same chamber volume and motor power can produce very different results in year three, and the difference is in four things that do not appear on a specification sheet.

1. Wetted-part metallurgy

Chamber liner and rotor material determine wear life on an abrasive pigment far more than the motor rating does. Ask for the specific grade, not "stainless steel".

2. Mechanical seal design and support

The seal is the part that fails first. A seal with its own cooling and flushing circuit lasts materially longer than one running on product alone — and on pigment, product alone means abrasive particles against the faces.

3. Separation system

Whether the dynamic gap holds its setting under thermal cycling, and whether the screen is replaceable in the field. This is also what caps the achievable fineness.

4. Documentation and spares

A machine with a parts list and dimensional drawings is maintainable a decade later; one without them is a machine that gets replaced early. Ask for both before ordering, not after.

A supplier who answers all four in writing is a different supplier from one who answers with a price. For context on how the market divides, our comparison of bead mill manufacturers covers what to look for across geographies.

Before You Request a Quote: 7 Things to Send

These answers turn a price into a specification:

  • Pigment and grade. Organic or inorganic, and the specific grade — surface treatment differs between suppliers of the same color index.
  • Vehicle and solids loading. Determines viscosity and therefore which machine family is even possible.
  • Target fineness and the gauge. A Hegman number or a micron figure; "fine" is not a specification.
  • Throughput per hour and whether the operation is single pass or recirculation.
  • Temperature ceiling of the vehicle system, since this decides cooling sizing and sometimes rules out media milling entirely.
  • Batch size and color-change frequency, which decides basket against horizontal.
  • Site conditions. Electrical supply and frequency, available floor space, and whether solvent or combustible dust requires an explosion-proof configuration.

Where the Machine Is Built: 9,000 m² in Wuxi

POLYC manufactures in Wuxi, Jiangsu, on a 9,000 square meter factory established in 2006, with 19 years of export experience. Chambers, rotors, pin stacks and hydraulic assemblies are built and assembled in-house, which is why a non-standard chamber volume, rotor spacing or wetted material is a configuration question rather than a new development project. Machines carry a 3-year global warranty and ship in 30 to 45 days.

POLYC manufacturing floor in Wuxi where pigment milling equipment is assembled
The Wuxi workshop floor, where the mills described in this guide are built and assembled.

Factory inspection is welcome, and a trial run on your own pigment and vehicle can be arranged before an order — which is the most direct way to confirm that a proposed machine and media combination reaches your target.

Go Deeper: Question Index

This guide covers pigment milling end to end. The questions below need a page of their own, and each is answered by the single best hand-written page we have on it.

By machine type

By decision

By pigment process

Sourcing

About This Guide

POLYC Technology manufactures wet grinding and dispersion machinery in Wuxi, Jiangsu, and operates a testing facility where customer pigments are milled and measured before a machine specification is fixed. The model specification tables in this guide are taken from our published product data. The pigment-to-machine and bead-size guidance reflects general industry practice rather than measurements we have taken on your material — real performance depends on pigment grade, solids loading, vehicle and pass strategy, which is why we recommend a trial on your own formulation before committing to a purchase.

References and Sources

Where this guide refers to a measurement standard, these are the documents concerned. Model specifications come from POLYC product data; industry ranges are labelled as such in the text.

  • ISO 13320:2020 — Particle size analysis — Laser diffraction methods. International Organization for Standardization. The standard behind the particle size figures a laser analyser reports.
  • ISO 787 series — General methods of test for pigments and extenders. International Organization for Standardization. Covers the test methods used to characterise pigment before and after milling.
  • ASTM D1210 — Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems. ASTM International. The Hegman gauge method referenced throughout this guide.
  • ISO 8780 / ISO 8781 series — Dispersion methods and assessment of dispersion characteristics. International Organization for Standardization. How dispersion behavior is evaluated consistently rather than by eye.
  • ISO 1524:2020 — Paints, varnishes and printing inks — Determination of fineness of grind. International Organization for Standardization. The international fineness-of-grind method that sits behind the Hegman reading.
  • ISO 8781-1:1990 — Pigments and extenders — Methods of assessment of dispersion characteristics — Part 1: Assessment from the change in tinting strength of coloured pigments. International Organization for Standardization. The method for measuring color strength development, which is what this guide means by color strength.

Send the Pigment, the Target Fineness in µm, and the Batch

Tell us the pigment, the vehicle, the target fineness with the gauge you measure it with, and the throughput per hour. Our engineers will confirm the machine route, chamber volume, motor power, separation system and media recommendation. Quoted directly from the Wuxi factory, with a 3-year global warranty. Reply within 24 hours.

Request a configured quoteChat on WhatsApp

19+ yearsexport experience
ISO 9001 & CEcertified
3-yearglobal warranty
30–45 daysdelivery
100%customizable

Frequently Asked Questions

What is pigment milling equipment?
It is the machinery that reduces pigment particles and breaks up agglomerates inside a liquid vehicle. The family covers high speed dispersers for wetting and de-agglomeration, bead and basket mills for true size reduction, and three roll mills for high-viscosity pastes. A pigment line normally uses two or three of these in sequence rather than one machine doing everything.
Do I need a bead mill or just a disperser for pigment?
A disperser wets out powder and breaks agglomerates down to roughly the primary particle size, but it cannot reduce primary particles. If your Hegman reading stops improving after the dispersion stage, you have reached that limit and further disperser time buys nothing. Reaching finer requires media milling. Many pigment processes do dispersion first, then one pass through a bead mill.
What bead size should I use for pigment grinding?
Start from the target fineness rather than from the media you happen to have in stock. As an industry rule of thumb, the achievable particle size is roughly one thousandth of the bead diameter, so 1 mm media target around 1 micron and 0.3 mm media reach sub-micron. Then confirm the separation system can retain that bead size — that check is what rejects most optimistic media plans. These ratios are general industry guidance, not figures we have measured on your product.
Why does my pigment lose color strength after milling?
Usually because the grind is over-extended or running too hot. Color strength peaks at a particular particle size for each pigment and then falls as particles get too small and the surface becomes more reactive. Running past that point also raises temperature, and heat drives flocculation and shade shift. Grinding longer is not always grinding better.
Can one machine handle both organic and inorganic pigments?
Mechanically yes, but the economics rarely work out on one machine. Inorganic pigments such as titanium dioxide are relatively easy to de-agglomerate and reach specification quickly. Organic pigments and carbon black need far more energy to wet out and de-agglomerate, so a machine sized for TiO2 will be badly under-powered for phthalocyanine blue. Most plants either size for the hardest pigment they run or keep a separate mill.
How do I compare pigment milling equipment manufacturers?
Ask four questions that only matter after year one: what is the chamber and rotor material, how is the mechanical seal cooled and flushed, what is the separation gap and how is it adjusted, and can you supply a parts list with dimensional drawings. A supplier who can answer all four in writing is a different supplier from one who answers with a price. Published capacity tables are the easiest thing to copy; answers about wear parts are not.
What fineness can pigment milling reach?
POLYC horizontal media mills are specified for grinding media of 0.2 to 1.5 mm and achievable fineness of 50 nm to 5 microns depending on the media and pass strategy. For most architectural and industrial coatings the practical target is 5 to 20 microns, which is well within range. Sub-micron is achievable but it is a different process decision, not just more passes.
Do I need explosion-proof equipment for pigment milling?
It depends on the solvent system and the dust classification on your site. Solvent-borne pigment pastes and dry powder handling can require it; water-borne systems often do not. Explosion-proof configurations available upon request — the correct classification has to come from your site assessment, not from a supplier catalogue.

Related Resources

Bead Mill: Types, Specifications and Price

The full range across disc, pin, nano and vertical frames on one parameter set.

How a Basket Mill Works

The single-vessel alternative for short runs and frequent pigment changes.

Color Strength in Pigment Paste

Where color strength is lost between the powder and the finished paste.

Pigment Production Line

How the machines above combine into a turnkey pigment or color paste line.

prev
Why a Viscous Paste Does Not Blend: Laminar Flow, Surface Renewal and the Wrong Question About Time
Bead Mill vs Three Roll Mill: Which Route for Your Paste?
next
recommended for you
Get in touch with us
The company always adheres to the principle of quality first, adhering to the concept of value sharing and service winning, to provide you with more energy saving and more advanced chemical production equipment.
Contact Us
Contact person: Peter Yu
Tel: +86 138 1677 4633
WhatsApp: +86 138 1677 4633

Add:
Shanghai office address: No.712, Block A, Greenland Supreme, 6167-6169, Oriental Meigu Avenue, Fengxian District, Shanghai


Copyright © 2026 Polyc Machine | Sitemap
Contact us
email
whatsapp
Contact customer service
Contact us
email
whatsapp
cancel
Customer service